Zprávy

How to Maintain the Laser Cutting Machine after Use?

How to Maintain the Laser Cutting Machine after Use?

2022-07-23 11:54:34

When doing the maintenance of the laser cutting machine, we should pay attention to cleaning the lens, guide rail, and sundries on the workbench every day. Next, follow us to see the maintenance methods of different parts.

 

LASER CUTTING

 

How to maintain the laser cutting machine?

 

Lens cleaning method: when cleaning the lens, ethanol or 98% alcohol must be used as the cleaning solution, and a small amount of absorbent cotton is gently stained with alcohol, and then placed on the lens.

 

Gently directionally scrub the lens, and then wipe the lens with a dry cotton cloth to make the lens bright and transparent.

 

Note: when scrubbing too hard, it is easy to wipe off the coating on the lens until the lens is damaged.

 

Cleaning method of the guide rail: first remove the stains on the guide rail, and deal with them. After crushing the materials, add a little clean lubricating oil to the guide rail, and move the guide rail so that the clean lubricating oil can be evenly distributed on the guide rail. Be careful not to thicken the lubricating oil (butter). This kind of lubricating oil attached to the guide rail is easy to cause the adhesion and distortion of processed materials and dust, thus damaging the slider and guide rail.

 

Cleaning method of the working platform. There is zinc on the working platform, such as ferroalloy, honeycomb briquette, crawler, knife bar, etc. clean up the processing waste on the working platform first. After half a year of use, the crawler worktable needs to be treated with a little clean antirust oil on the crawler, and other worktables do not need it.

 

Note: the working platform cannot be easily cleaned with water. It is easy to rust the working platform and accelerate the oxidation of the work.

 

Maintain the correct operation process of laser cutting machine focus lens

 

  1. Take out the focusing lens from the frame: loosen the fastening screws, remove the air nozzle and lens barrel in turn, and blow the dust off the lens surface with a blowing balloon first.

 

  1. If you need to clean the lens, you can only use a laboratory-grade paper soft cotton ball, dip it in an appropriate amount of acetone or high-content alcohol, and rotate it gently clockwise from the center of the lens to the edge. If necessary, both sides of the lens need to be cleaned. Pay attention when scrubbing.

 

  1. Install the lens barrel and air nozzle, adjust the focal length, tighten the fastening screws, and keep the convex face downward when installing the focusing lens.

 

When maintaining the focusing lens of the laser cutter kit, pay attention to the following three points:

 

  1. The focusing lens material is ZnSe (arsenic zinc), which is brittle and afraid of falling; Attention during disassembly: do not use too much force, and do not collide with hard objects. There is a layer of antireflective film on the surface, which is afraid of pollution, humidity, greasy, and scratch; Therefore, it is necessary to provide dry and degreased air during work. Do not operate the focusing lens directly by hand, because the skin is oily. This will damage the lens surface. Instead, you can wear gloves and a special suit to operate. For smaller lenses, it is more convenient to use optical tweezers or vacuum tweezers. No matter what method is used to clamp the focusing lens of the laser machine, it can only be clamped along the non-optical surface, such as the frosted edge of the plaque.

 

  1. Under normal circumstances, it is necessary to check the condition of the focusing lens before use and before and after cleaning. Due to the relatively small size of most pollutants and surface defects, we often need to use amplification equipment when checking the lens. In addition to amplification equipment, sometimes we need to irradiate the optical surface with relatively bright light to enhance the specular reflection intensity of surface pollutants and defects so that pollutants and defects can be more easily found.

 

  1. When cleaning the focus lens, always use clean wiping paper and optical grade solvent to prevent damage by other pollutants. The wiping paper must be soaked with a suitable solvent and cannot be used dry. Considering the softness, the available wiping paper is pure cotton wiping paper or applicator, such as cotton balls, lens paper towels, and cotton swabs.

 

Although the cleaning and maintenance of the focus lens are troublesome, good cleaning and maintenance operations can prolong the service life of the lens, improve work efficiency, and save costs for enterprises, which can be described as getting twice the result with half the effort. When the cleanliness is still not reached after repeated cleaning, please pay attention to replacement to ensure the processing efficiency of the laser cutting machine, so as not to delay production.

 

Searching for a cnc laser cutting steel, cnc laser cut steel, laser for cnc cutting metal supplier, wholesaler, manufacturer from China, you can get high-quality products at a nice price.

Kontaktujte nás
název

název can't be empty

* E-mailem

E-mailem can't be empty

Telefon

Telefon can't be empty

Společnost

Společnost can't be empty

* Zpráva

Zpráva can't be empty

Předložit